K201B
سلسلة كاشطة قاطع التغذية K201B
يقذف3 1/2 بوصة (89 مم)
Chain unit21 بوصة (534 مم)
عرض الكاشطة44 2/5 بوصة (1127.5 مم)
K Series feeder breaker scraper chain with a 21 inch repeating unit and 44 2/5 inch scraper width.
سلسلة قاطع التغذية K201Bسلسلة قاطع التغذية K207Bمرجع درجة الصوت 3.5 بوصةدعم قياس الاستبدالتطبيقات التعدين تحت الأرضسلسلة قاطع التغذية K201Bسلسلة قاطع التغذية K207Bمرجع درجة الصوت 3.5 بوصةدعم قياس الاستبدالتطبيقات التعدين تحت الأرض
FEEDER BREAKER CHAIN SPECIALIST
Focused Chain Selection for Feeder Breaker Conveyors
Feeder breaker chain selection should start with the geometry and duty of the installed conveying system, not with a generic mining-chain size list. The chain, scraper or flight arrangement, sprocket engagement and machine interface work together, so a replacement review should compare the details that control fit: pitch, repeating chain-unit length, scraper width, link and joint structure, flight arrangement and the condition of the existing assembly.
The current feeder breaker range is centred on the K Series and the K201B and K207B feeder breaker scraper chain configurations. Both models use a nominal 3 1/2 inch pitch, while their specified widths and component structures provide important identification points. Where the installed chain is unknown or has been repaired in service, photographs, measurements and the existing drawing should be reviewed together before an order is released.
PRODUCT RANGE
Feeder Breaker Chain Models
All products assigned to the Feeder Breaker Chain category are shown below as live catalogue cards. Each card uses the product main image, the model-specific dimensions currently published for that product and a direct link to the detailed product page.
K207B
سلسلة كاشطة قاطع التغذية K207B
يقذف3 1/2 بوصة (88.9 مم)
Chain unit21 بوصة (533.4 مم)
عرض الكاشطة46 بوصة (1171.85 ملم)
K Series feeder breaker scraper chain with a 21 inch repeating unit, 46 inch scraper width and model-specific scraper outer-link structure.
APPLICATION CONTEXT
Where Feeder Breaker Chains Work
The K Series product information covers underground feeder breaker chain conveyors and coal-handling or coal-washing service. The illustrations below are used to explain the operating context; machine-specific limits, tension values and maintenance procedures should always follow the approved equipment documentation.
Underground Feeder Breaker Conveying
Heavy chain and scraper assemblies move material through the feeder breaker while operating in a confined, contamination-prone mining environment.
Coal Handling & Washing Service
Coal-handling duty makes chain geometry, flight arrangement, wear condition and sprocket engagement important parts of replacement planning.
Inspection & Replacement Review
Record the installed condition before removal. Overall photographs, joint close-ups and dimensional reference points help preserve the original configuration.
SELECTION LOGIC
Four Checks Before Model Selection
A nominal pitch is an important starting point, but it is not a complete product identity. Use the four checks below together when comparing a known model or an unidentified chain.
يقذف
Measure between corresponding joint centres. Where access permits, measuring across several pitches can reduce field-reading error.
Repeating Chain Unit
Record the repeating assembly length containing the chain sections and the flight or scraper section rather than a random overall length.
Scraper Width
Overall scraper width is a practical discriminator between K201B and K207B and should be recorded with the measurement reference points.
Component Structure
Compare inner and outer links, bushes, pins, scraper or flight connection details and any distinctive retention or extended-pin features.
MODEL COMPARISON
K201B vs K207B at a Glance
The models share a nominal 3 1/2 inch pitch, but the specified metric values, scraper widths and component trees differ. The table is an identification aid, not an interchangeability statement.
| Selection point | K201B | K207B |
|---|---|---|
| يقذف | 3 1/2 بوصة (89 مم) | 3 1/2 بوصة (88.9 مم) |
| طول وحدة السلسلة | 21 بوصة (534 مم) | 21 بوصة (533.4 مم) |
| عرض الكاشطة | 44 2/5 بوصة (1127.5 مم) | 46 بوصة (1171.85 ملم) |
| Secondary structure | Chain Section, Outer Link, Inner Link, Flight Section | Chain Section, Outer Link, Inner Link, Scraper Outer Link, Flight Section |
| Distinctive items in component tree | Locating Bush, Spring Pin | Extended Pin, T-Pin |
WHY A FOCUSED RANGE HELPS
A Clearer Procurement Path for Heavy Mining Chain
The site is structured around a small number of feeder breaker configurations so each model can carry the dimensions, component structure, application context and RFQ guidance that a maintenance or purchasing team actually needs.
Model-Specific Data
K201B and K207B keep their own dimensions and component identities instead of being blended into a generic chain table.
Measurement-Led Review
Unknown replacement chains are reviewed from measurable geometry, photographs and the equipment context.
Clear RFQ Scope
Missing technical values become confirmation questions rather than unsupported assumptions.
Engineering Routing
Selection, pitch, components, maintenance, tension and wear are separated into focused guides for faster technical review.
CUSTOM & UNIDENTIFIED CHAIN REVIEW
When the Installed Chain Does Not Match a Standard Model
A field chain may have lost its marking, been repaired, or differ from the controlled drawing. In that case, the request should be treated as an identification or custom-configuration review rather than forcing the chain into the nearest model name.
Provide the measured pitch, repeating chain-unit length, scraper width, flight spacing, link and joint details, photographs and a measured sketch or historical drawing. If material, heat treatment, hardness, testing, marking or traceability requirements are customer-controlled, include them in the purchase specification. Unknown requirements should remain open for confirmation.
MANUFACTURING & INSPECTION
From Components to a Controlled Chain Assembly
Manufacturing images are used to explain the type of machining, assembly and dimensional-control work involved in heavy chain production. Order-specific material, heat-treatment, hardness, inspection or documentation requirements should be stated on the controlled drawing or purchase specification when they apply.
Component Machining
Link plates, pins and bushes require controlled geometry so the assembled joint can be reviewed against the specified chain configuration.
Assembly Control
The chain section, joint components and flight or scraper connection must be assembled as one coordinated configuration.
Dimensional Inspection
Pitch, width and relevant component dimensions should be checked against the approved order data rather than assumed from appearance alone.
RFQ PREPARATION
Make the First Technical Review Useful
For a known K201B or K207B request, send the model, quantity and the drawing or previous controlled purchase reference if available. For an unknown replacement chain, include overall and close-up photographs, measured pitch, repeating chain-unit length, scraper width, flight arrangement, visible link and retention details, machine context and any markings that remain readable.
Known modelModel + quantity + drawing/reference
Unknown modelPhotos + core dimensions + machine context
Custom configurationMeasured sketch + controlled requirements
Service conditionMaterial handled + wear/damage observations
Do not guess a missing dimension or copy a value from another chain. Mark unknown items clearly so they can be resolved during review.
TECHNICAL LIBRARY
Latest Feeder Breaker Chain Guides
Field-focused articles cover measurement, inspection records, component identification, wear observations and replacement preparation without duplicating the primary product-page keywords.
الدليل الفني
قائمة مراجعة طلب عروض أسعار لسلسلة قاطع التغذية تحت الأرض لفرق الصيانة
استخدم قائمة التحقق هذه الخاصة بطلب عروض أسعار سلسلة قاطع التغذية تحت الأرض لالتقاط سياق الآلة، وهندسة السلسلة، والصور، والرسومات، والحالة، والكمية، و.
اقرأ الدليل →
الدليل الفني
سلسلة كاشطة لآلة التعدين ذات التغذية والكسر أو آلة التعدين ذات التثبيت؟ ما هي الأدلة المطلوبة؟
افصل استعلامات سلسلة الكسارة المغذية عن سلسلة كاشطة التعدين باستخدام سياق الآلة، والهندسة المتكررة، وتفاصيل الرحلة، والأبعاد، والعلامات، و.
اقرأ الدليل →
الدليل الفني
قاطع التغذية أم سلسلة عربات النقل؟ كيفية توجيه استفسار غير واضح
توجيه استفسار غير واضح حول قاطع التغذية مقابل سلسلة عربة النقل باستخدام سياق المعدات، والهندسة الكاملة للسلسلة، وأدلة الرحلة، والعلامات، والرسومات.
اقرأ الدليل →
الدليل الفني
كيفية تسجيل سجل تعديل سلسلة قاطع التغذية لتحسين التشخيص
قم بإنشاء سجل تاريخي لتعديل سلسلة قواطع التغذية يربط كل تغيير بالقياسات والأعراض وسياق التشغيل والتحقق بعد التعديل.
اقرأ الدليل →
الدليل الفني
كيفية تنسيق استبدال سلسلة قاطع التغذية مع فحص العجلة المسننة
قم بتنسيق استبدال سلسلة قاطع التغذية مع فحص العجلة المسننة من خلال تسجيل حالة الأسنان، ودليل التعشيق، والمحاذاة، وهندسة السلسلة.
اقرأ الدليل →
الدليل الفني
كيفية توثيق حالة الدبابيس والبطانات في سلسلة قاطع التغذية
حالة دبوس سلسلة قاطع تغذية المستندات وجلبة التثبيت مع موقع المفصل، والصور المزدوجة، وملاحظات التمفصل، والقياسات، ونمط التآكل، و.
اقرأ الدليل →
